電子發燒友App
今天給大俠帶來FPGA設計中，對SPI進行參數化結構設計，話不多說，上貨。 ?
為了避免每次SPI驅動重寫，直接參數化，盡量一勞永逸。SPI master有啥用呢，你發現各種外圍芯片的配置一般都是通過SPI配置的，只不過有三線和四線。SPI slave有什么用呢，當外部主機（cpu）要讀取FPGA內部寄存器值，那就很有用了，FPGA寄存器就相當于RAM，cpu通過SPI尋址讀寫數據。代碼僅供參考，勿做商業用途。
SPI salve
SPI salve支持功能：
支持三線SPI或者四線SPI。通過define切換。??? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?
支持指令長度、幀長自定義。? ??? ? ? ? ? ? ? ? ? ? ? ? ? ?
工作時鐘可自定義，大于SPI clk的2倍。
用戶只需修改：（1）幾線SPI。（2）單幀長度。（3）指令長度。（4）寄存器開辟。
注意：指令最高bit表示讀寫，低寫高讀，其余bit表示地址。指令接著為數據端，兩者位寬之和即為SPI單幀長。
//`define SPI_LINE //是否是三線SPI `define SPI_FRAME_WIDTH 16 //SPI一幀長度為16 `define SPI_INS_WIDTH 8 //SPI指令長 `timescale 1ns/1ps //// module spi_slave ( input i_clk , //work clk input i_rst_n , input i_spi_clk , //SPI clk input i_spi_cs , //SPI cs `ifdef SPI_LINE //條件編譯 inout io_spi_sdio `else input i_spi_mosi , //SPI mosi output o_spi_miso //SPI miso `endif ); //位寬計算函數 function integer clogb2 (input integer depth); begin for (clogb2=0; depth>0; clogb2=clogb2+1) depth = depth >>1; end endfunction reg r_cs = 1'b1; //打一拍 always @(posedge i_clk) begin r_cs <= i_spi_cs; end reg [1:0] r_spi_clk_edge = 2'b00; //SPI clk邊沿檢測 always @(posedge i_clk) begin r_spi_clk_edge <= {r_spi_clk_edge[0],i_spi_clk}; end //always reg [clogb2(`SPI_FRAME_WIDTH-1)-1:0] r_spi_cnt = 'd0; always @(posedge i_clk) begin if (r_cs) //cs為高則歸零 r_spi_cnt <= 'd0; else if (r_spi_clk_edge == 2'b10) //下降沿才計數 r_spi_cnt <= r_spi_cnt + 'd1; end ////指令鎖存 reg [`SPI_INS_WIDTH-1:0] r_ins = 'd0; always @(posedge i_clk) begin if ((~r_cs) && (r_spi_clk_edge == 2'b01)) //上升沿鎖存數據 begin if ((r_spi_cnt >= 0) && (r_spi_cnt <= `SPI_INS_WIDTH-1)) `ifdef SPI_LINE //條件編譯 r_ins <= {r_ins[`SPI_INS_WIDTH-2:0],io_spi_sdio}; `else r_ins <= {r_ins[`SPI_INS_WIDTH-2:0],i_spi_mosi}; `endif end end ////數值寫入 reg [`SPI_FRAME_WIDTH-`SPI_INS_WIDTH-1:0] r_data_rx = 'd0; always @(posedge i_clk) begin if ((~r_cs) && (r_spi_clk_edge == 2'b01)) //上升沿鎖存數據 begin if (r_spi_cnt >= `SPI_INS_WIDTH) `ifdef SPI_LINE r_data_rx <= {r_data_rx[`SPI_FRAME_WIDTH-`SPI_INS_WIDTH-2:0],io_spi_sdio}; `else r_data_rx <= {r_data_rx[`SPI_FRAME_WIDTH-`SPI_INS_WIDTH-2:0],i_spi_mosi}; `endif end end ////用戶寄存器定義 reg [`SPI_FRAME_WIDTH-`SPI_INS_WIDTH-1:0] r_reg0 = 'd0; reg [`SPI_FRAME_WIDTH-`SPI_INS_WIDTH-1:0] r_reg1 = 'd0; reg [`SPI_FRAME_WIDTH-`SPI_INS_WIDTH-1:0] r_reg2 = 'd0; reg [`SPI_FRAME_WIDTH-`SPI_INS_WIDTH-1:0] r_reg3 = 'd0; //// always @(posedge i_clk,negedge i_rst_n) begin if (~i_rst_n) begin r_reg0 <= 'd0; r_reg1 <= 'd0; r_reg2 <= 'd0; r_reg3 <= 'd0; end else if ((~r_ins[`SPI_INS_WIDTH-1]) && (r_spi_cnt == (`SPI_FRAME_WIDTH-1)) && (~r_cs) && (r_spi_clk_edge == 2'b01)) begin `ifdef SPI_LINE case (r_ins[`SPI_INS_WIDTH-2:0]) 'd0:begin r_reg0 <= {r_data_rx[`SPI_FRAME_WIDTH-`SPI_INS_WIDTH-2:0],io_spi_sdio}; end 'd1:begin r_reg1 <= {r_data_rx[`SPI_FRAME_WIDTH-`SPI_INS_WIDTH-2:0],io_spi_sdio}; end 'd2:begin r_reg2 <= {r_data_rx[`SPI_FRAME_WIDTH-`SPI_INS_WIDTH-2:0],io_spi_sdio}; end 'd3:begin r_reg3 <= {r_data_rx[`SPI_FRAME_WIDTH-`SPI_INS_WIDTH-2:0],io_spi_sdio}; end endcase `else case (r_ins[`SPI_INS_WIDTH-2:0]) 'd0:begin r_reg0 <= {r_data_rx[`SPI_FRAME_WIDTH-`SPI_INS_WIDTH-2:0],i_spi_mosi}; end 'd1:begin r_reg1 <= {r_data_rx[`SPI_FRAME_WIDTH-`SPI_INS_WIDTH-2:0],i_spi_mosi}; end 'd2:begin r_reg2 <= {r_data_rx[`SPI_FRAME_WIDTH-`SPI_INS_WIDTH-2:0],i_spi_mosi}; end 'd3:begin r_reg3 <= {r_data_rx[`SPI_FRAME_WIDTH-`SPI_INS_WIDTH-2:0],i_spi_mosi}; end endcase `endif end end ////寄存器值讀出 reg [`SPI_FRAME_WIDTH-`SPI_INS_WIDTH-1:0] r_data_tx = 'd0; always @(posedge i_clk) begin if (r_ins[`SPI_INS_WIDTH-1] && (~r_cs) && (r_spi_clk_edge == 2'b10)) begin if (r_spi_cnt == (`SPI_INS_WIDTH-1)) begin case (r_ins[`SPI_INS_WIDTH-2:0]) 'd0:begin r_data_tx <= r_reg0; end 'd1:begin r_data_tx <= r_reg1; end 'd2:begin r_data_tx <= r_reg2; end 'd3:begin r_data_tx <= r_reg3; end endcase end else r_data_tx <= {r_data_tx[`SPI_FRAME_WIDTH-`SPI_INS_WIDTH-2:0],1'b0}; end end ////讀取輸出 `ifdef SPI_LINE assign io_spi_sdio = (r_ins[`SPI_INS_WIDTH-1]) ? (((r_spi_cnt>=`SPI_INS_WIDTH) && (r_spi_cnt<`SPI_FRAME_WIDTH)) ? r_data_tx[`SPI_FRAME_WIDTH-`SPI_INS_WIDTH-1] : 1'bz) : 1'bz; `else assign o_spi_miso = ((r_spi_cnt>=`SPI_INS_WIDTH) && (r_spi_cnt<`SPI_FRAME_WIDTH)) ? r_data_tx[`SPI_FRAME_WIDTH-`SPI_INS_WIDTH-1] : 1'b0; `endif endmodule // end the spi_slave model
SPI master
spi master內部?jì)H僅封裝SPI驅動，寫入值讀出控制由上層控制，這部分邏輯很simple，不贅述。用戶只需給入SPI幀及控制使能即可。
用戶只需修改parameter參數：（1）單幀長；（2）指令長；（3）數據長；（4）工作時鐘；（5）SPI clk。
實現不使用狀態機，采用線性序列計數法。
//`define SPI_LINE //是否是三線SPI
`timescale 1ns/1ps
module spi_master
#(parameter p_spi_frame_width = 16, //SPI單幀長度
parameter p_spi_ins_width = 8 , //指令長度
parameter p_spi_data_width = 8 //讀出數據長度
)
(
input i_clk , //系統時鐘
input i_rst_n ,
input i_flag , //檢測到flag的上升沿則啟動一次傳輸,一個時鐘周期即可
input [p_spi_frame_width-1:0] i_spi_data ,
output o_spi_cs ,
output o_spi_clk ,
`ifdef SPI_LINE //條件編譯
inout io_spi_sdio ,
`else
input i_spi_miso , //SPI miso
output o_spi_mosi , //SPI mosi
`endif
output o_transfer_done , //單次傳輸完成
output [p_spi_data_width-1:0] o_spi_data //讀取數據
);
parameter p_clk_fre = 200; //XXM時鐘頻率
parameter p_spi_clk_fre = 0.5*1000; //SPI 時鐘速率,表示1M
parameter p_clk_div = p_clk_fre * 1000/p_spi_clk_fre/2-1;
parameter p_spi_cnt_max = p_spi_frame_width*2-1;
parameter p_spi_ins_max = p_spi_ins_width*2-1;
//位寬計算函數
function integer clogb2 (input integer depth);
begin
for (clogb2=0; depth>0; clogb2=clogb2+1)
depth = depth >>1;
end
endfunction
//把最大值賦值給線型，直接用p_clk_div仿真有問題，但實際上板是可以的
wire [clogb2(p_clk_div)-1:0] w_clk_div;
assign w_clk_div = p_clk_div;
////時鐘分頻
reg [clogb2(p_clk_div)-1:0] r_cnt_div = 'd0;
always @(posedge i_clk)
begin
if (r_cnt_div == w_clk_div)
r_cnt_div <= 'd0;
else
r_cnt_div <= r_cnt_div + 'd1;
end //always
wire w_clk_en; //分頻時鐘使能
assign w_clk_en = (r_cnt_div == w_clk_div) ? 1'b1 : 1'b0;
reg [1:0] r_flag_edge = 2'b00;
reg [clogb2(p_spi_cnt_max)-1:0] r_spi_cnt = 'd0;
always @(posedge i_clk) //flag邊沿檢測
begin
r_flag_edge <= {r_flag_edge[0],i_flag};
end
//flag信號展寬到低速時鐘域
reg r_flag_enlarge = 1'b0;
always @(posedge i_clk)
begin
if (r_flag_edge == 2'b01) //上升沿拉高
r_flag_enlarge <= 1'b1;
else if (r_spi_cnt == p_spi_ins_max) //足夠長的高電平才拉低
r_flag_enlarge <= 1'b0;
end
reg [1:0] r_flag_enlarge_edge = 2'b00;
always @(posedge i_clk)
begin
if (w_clk_en)
r_flag_enlarge_edge <= {r_flag_enlarge_edge[0],r_flag_enlarge};
end
reg r_cs = 1'b1;
always @(posedge i_clk)
begin
if (w_clk_en)
begin
if (r_flag_enlarge_edge == 2'b01) //檢測到需要進行SPI操作
r_cs <= 1'b0;
else if (r_spi_cnt == p_spi_cnt_max) //計數到最大值表示一次SPI完成
r_cs <= 1'b1;
end
end
always @(posedge i_clk)
begin
if (w_clk_en)
begin
if(~r_cs) //在操作區間計數
r_spi_cnt <= r_spi_cnt + 'd1;
else
r_spi_cnt <= 'd0;
end
end
////數據傳輸段
reg [p_spi_frame_width-1:0] r_data = 'd0;
always @(posedge i_clk)
begin
if (w_clk_en)
begin
if (r_flag_enlarge_edge == 2'b01) //上升沿刷入
r_data <= i_spi_data;
else if (r_spi_cnt[0] == 1'b1) //數據移動
r_data <= {r_data[p_spi_frame_width-2:0],1'b1};
end
end
////數據讀取段
reg [p_spi_data_width-1:0] r_data_read = 'd0;
always @(posedge i_clk)
begin
if (w_clk_en)
begin
if (i_spi_data[p_spi_frame_width-1] && (r_spi_cnt > p_spi_ins_max) && (r_spi_cnt[0] == 1'b0)) //是讀
`ifdef SPI_LINE
r_data_read <= {r_data_read[p_spi_data_width-2:0],io_spi_sdio};
`else
r_data_read <= {r_data_read[p_spi_data_width-2:0],i_spi_miso};
`endif
end
end
////SPI輸出段
assign o_spi_cs = r_cs;
assign o_spi_clk = r_cs ? 1'b0 : r_spi_cnt[0];
////SPI SDIO的輸入輸出切換
`ifdef SPI_LINE
assign io_spi_sdio = (i_spi_data[p_spi_frame_width-1]) ? (((r_spi_cnt >= 'd0) && (r_spi_cnt <= p_spi_ins_max)) ? r_data[p_spi_frame_width-1] : 1'bz ) : r_data[p_spi_frame_width-1];
`else
assign o_spi_mosi = r_data[p_spi_frame_width-1];
`endif
assign o_transfer_done = ((~r_cs) && (r_spi_cnt == p_spi_cnt_max)) ? 1'b1:1'b0;
assign o_spi_data = r_data_read;
endmodule // end the spi_master model
?
?
仿真如下所示：寫入四個寄存器值，再讀出。
仿真代碼如下：
?
?
`define TRANSFER_NUMBER 8 //操作數為4 `define DATA 8'ha5 //`define SPI_LINE timeunit 1ns; timeprecision 1ps; module top; parameter p_sim_end_time = 1000000; //ns logic l_clk = 1'b0; always #2.5 l_clk = ~l_clk; ////復位 logic l_rst_n = 1'b0; initial begin #100 l_rst_n = 1'b1; end wire io_sdio; wire o_spi_cs; wire o_spi_clk; wire o_transfer_done; wire [7:0] o_spi_data; ////多個數據操作模式 reg r_flag = 1'b0; reg [1:0] r_first_cnt = 2'b00; always @(posedge l_clk,negedge l_rst_n) begin if (~l_rst_n) r_first_cnt <= 2'b00; else if (r_first_cnt == 2'd3) r_first_cnt <= r_first_cnt; else r_first_cnt <= r_first_cnt + 2'd1; end reg [1:0] r_transfer_done_edge = 2'b00; always @(posedge l_clk) begin r_transfer_done_edge <= {r_transfer_done_edge[0],o_transfer_done}; end reg [3:0] r_transfer_cnt = 4'd0; always @(posedge l_clk) begin if ((r_first_cnt == 2'd2) && (r_transfer_cnt < `TRANSFER_NUMBER)) r_flag <= 1'b1; else if ((r_transfer_done_edge == 2'b10) && (r_transfer_cnt < `TRANSFER_NUMBER-1)) r_flag <= 1'b1; else r_flag <= 1'b0; end always @(posedge l_clk) begin if (r_transfer_done_edge == 2'b10) r_transfer_cnt <= r_transfer_cnt + 'd1; end reg [15:0] r_in_data = 16'd0; always @(*) begin if (~l_rst_n) //仿真不執行此段仿真會(huì )有問題 r_in_data = 16'h0000; else begin case(r_transfer_cnt) 4'd0:begin r_in_data = {8'h00,8'h43}; end 4'd1:begin r_in_data = 16'h0132; end 4'd2:begin r_in_data = 16'h0245; end 4'd3:begin r_in_data = 16'h0367; end 4'd4:begin r_in_data = 16'h8000; end 4'd5:begin r_in_data = 16'h8100; end 4'd6:begin r_in_data = 16'h8200; end 4'd7:begin r_in_data = 16'h8300; end default:begin r_in_data = 16'h0000; end endcase end end wire w_spi_miso; wire w_spi_mosi; spi_master inst_spi_master ( .i_clk (l_clk), .i_rst_n (), .i_flag (r_flag), .i_spi_data (r_in_data), .o_spi_cs (o_spi_cs), .o_spi_clk (o_spi_clk), `ifdef SPI_LINE .io_spi_sdio (io_sdio), `else .i_spi_miso (w_spi_miso), .o_spi_mosi (w_spi_mosi), `endif .o_transfer_done (o_transfer_done), .o_spi_data (o_spi_data) ); spi_slave inst_spi_slave ( .i_clk (l_clk), .i_rst_n (l_rst_n), .i_spi_clk (o_spi_clk), .i_spi_cs (o_spi_cs), `ifdef SPI_LINE .io_spi_sdio (io_sdio) `else .i_spi_mosi (w_spi_mosi), .o_spi_miso (w_spi_miso) `endif ); initial begin #p_sim_end_time $stop; end endmodule
三線SPI：
四線SPI：
?
可以看到讀寫是一致的，驗證通過。
審核編輯：黃飛
?
工商網監
評論